Direct answer: A single-cable (hybrid) servo connection carries power, encoder signal and brake in one cable with one combined connector — used by Siemens S210 (S-1FK2) drives. A dual-cable connection uses two separate cables (power + encoder/brake) — used by V90 (S-1FL6) and S120 (S-1FK7). You cannot freely convert one to the other; the drive and motor must support it natively. Match the cable style to the drive series, then match pinout, shielding, cross-section and flex rating.
What “Single-Cable” and “Dual-Cable” Actually Mean
The terms describe how many physical cables run between the servo drive and the motor:
| Style | Cables | What runs through them | Siemens example |
|---|---|---|---|
| Single-cable (hybrid / OCC) | 1 | Power + encoder signal + brake, combined | S210 (S-1FK2), family 6FX5002-8QN** |
| Dual-cable | 2 | One power cable, one encoder/brake cable | V90 (S-1FL6) 6FX3002-*, S120 (S-1FK7) 6FX5002-2*/5* |
“One Cable Connection” (OCC) is Siemens’ name for the single-cable hybrid design. The whole point is fewer connectors, less wiring and a smaller bend radius — at the cost of a more complex combined connector.
Side-by-Side Comparison
| Dimension | Single-cable (S210 hybrid) | Dual-cable (V90 / S120) |
|---|---|---|
| Number of cables | 1 | 2 |
| Connectors | One combined connector | Separate power + encoder connectors |
| Wiring effort | Less; faster commissioning | More; more cable routing and tie-down |
| Space in the drag chain | Less | More |
| Weight / bend radius | Lower / tighter | Higher / larger |
| Cable cost | Higher per meter | Lower per meter |
| Typical length range | 0.3–70 m | 0.3–100 m (S120) |
| Best fit | New, compact machines; cobots; retrofit where OCC is native | Existing equipment, high-power, long runs |
The choice is dictated by the drive, not by preference. If the motor and drive only expose a two-connector interface, a single cable will not fit — and vice versa.
When to Choose Each
Choose single-cable (hybrid) when:
- Your drive is a Siemens S210 (S-1FK2) — it is designed for OCC.
- You are building compact machines, cobots or axes with tight cable carriers.
- You want faster assembly and fewer connection points to fail.
Choose dual-cable when:
- Your drive is a V90 (S-1FL6) or S120 (S-1FK7) — these use separate power and encoder/brake cables.
- You are replacing or extending cabling on existing equipment.
- You need long runs — S120 dual-cable assemblies are rated up to 100 m.
Part Numbers: Single-Cable vs Dual-Cable
This is the table to check against your BOM. (It continues the cross-reference from our earlier guide.)
| Drive series | Style | Siemens part number (examples) |
|---|---|---|
| S210 (S-1FK2) | Single-cable hybrid | 6FX5002-8QN04 · 6FX5002-8QN08 · 6FX5002-8QN11 · 6FX5002-8QN21 |
| V90 (S-1FL6) | Dual-cable — power | 6FX3002-2CT20 · 6FX3002-2CT12 · 6FX3002-2DB10 |
| V90 (S-1FL6) | Dual-cable — encoder/brake | 6FX3002-5CK01 · 6FX3002-5CL02 · 6FX3002-5BK02 |
| S120 (S-1FK7) | Dual-cable — power / encoder | 6FX5002-2DC10 · 6FX5002-2EQ20 · 6FX5002-5CN06 |
| Motor assembly | Dual-cable set | 6FX3502-7CD01-1AD0 · 6FX3502-5CL01 |
If your part number is not listed, request a cross-reference check — the program covers the full V90, S120 and S210 cable families.
Whatever the Style, Four Things Still Have to Match
Single-cable or dual-cable, a wrong match faults the drive:
- Connector pinout — the combined or separate connectors must map contact-for-contact to the drive socket.
- Shielding & EMC — the braid must be correctly bonded, or encoder noise causes position drift.
- Conductor cross-section — undersized cores overheat under load; oversized cores will not fit.
- Flex rating — fixed-installation cable fails in weeks inside a drag chain.
Where TENSOlink Fits
TENSOlink (tensolink.com) manufactures drop-in replacement servo cables for all three series above — single-cable for S210, dual-cable for V90 and S120 — matched to the same Siemens part numbers. Every cable is offered in three jacket grades under one program:
- SG — high-flex drag chain, rated for 10 million flex cycles.
- EG — fixed installation.
- PU — polyurethane, for oil, coolant and hydrolysis exposure.
Custom lengths from 0.3 m to 100 m with no extra charge for custom length, and stock items ship within 36 hours. For the mating side, sister brand Mosen (mosenc.com) supplies the M17 / M23 / M40 circular connectors — both the separate connectors for dual-cable and the combined connectors for single-cable hybrids.
FAQ
What is the difference between a single-cable and a dual-cable servo connection?
A single-cable (hybrid) connection carries power, encoder signal and brake in one cable with one combined connector; a dual-cable connection uses two separate cables (power + encoder/brake).
Which Siemens drives use single-cable (hybrid) connection?
The S210 (S-1FK2) series — identified by the 6FX5002-8QN** cable family.
Which Siemens drives use dual-cable connection?
V90 (S-1FL6) and S120 (S-1FK7), using the 6FX3002-* and 6FX5002-2*/5* families, plus 6FX3502 dual-cable motor-assembly sets.
Is a single-cable (OCC) connection cheaper?
The cable itself is usually more expensive per meter because of the combined connector, but the overall install is cheaper and faster — fewer cables, fewer connectors and less wiring time.
Can I convert a dual-cable drive to single-cable?
No. The drive and motor must support the single-cable interface natively; you cannot adapt a two-connector V90/S120 motor to a hybrid cable.
Does TENSOlink make both single-cable and dual-cable servo cables?
Yes — drop-in replacements for S210 single-cable, and V90/S120 dual-cable, matched to the same Siemens part numbers.
What lengths can I order?
Custom lengths from 0.3 m to 100 m (TENSOlink), with no extra charge for custom length.
About TENSOlink
TENSOlink (GUANGDONG TENSOLINK ELECTRIC CO., LTD.) is backed by a team that has manufactured replacement servo cable assemblies and M17/M23/M40 circular connectors since 2015, serving 2,000+ customers with drop-in replacements for Siemens V90, S120 and S210 drives. CE (LVD 2014/35/EU) and RoHS (2011/65/EU) certificates are held by the affiliated manufacturing entity, Guangzhou Tensolink Electric Co., Ltd. (USCC 91440111355804657U); ISO 9001 and SGS third-party test reports are held by the same entity.
References
- Siemens SINAMICS V90 operating instructions
- Siemens SINAMICS S210 servo drive system
- Directive 2014/35/EU — Low Voltage Directive (EUR-Lex)
- Directive 2011/65/EU — RoHS (EUR-Lex)
- PROFIBUS & PROFINET International — PROFINET cable specification