Servo Cables by Application: CNC, Robotics, Lithium Battery and More

Direct answer: The right servo cable is set by what the machine does to the cable — not just by the drive model. CNC and packaging machines need a high-flex drag-chain grade (SG) that survives millions of reciprocating bends. Robot arms and cobots need the same flex endurance plus tight bend-radius handling. Lithium-battery and welding equipment add strong EMI, so you want a shielded construction built for that noise. Medical and clean applications lean toward a polyurethane (PU) jacket that resists chemicals and is easy to keep clean. The drive side (pinout, connector, part number) still has to match your Siemens or third-party drive exactly.

Quick Reference: Application → Cable Choice

Application What the cable must survive Recommended grade
CNC machining Long stroke, repeated back-and-forth SG (high-flex, drag chain)
Packaging / printing / plastics Fast reciprocation, oils and coolant mist SG or PU (oil-resistant)
Industrial / collaborative robots Multi-axis flexing, tight bending SG high-flex, 10M+ flex cycles
Lithium battery / welding Strong electromagnetic interference Shielded construction, noise-optimized
Medical equipment Cleanliness, gentle flex, chemical exposure PU jacket, chemical-resistant

CNC Machines: Long Stroke, High Flex

A CNC axis does the same back-and-forth stroke thousands of times a day. Every stroke flexes the cable inside a carrier, which is exactly where a fixed-installation cable fails early. Choose a drag-chain (SG) grade rated for continuous flex — TENSOlink SG cables are specified for 10 million flex cycles — and route it inside a proper cable carrier so the bend radius is respected. Do not substitute a fixed-installation cable to save a few percent on a moving axis; the downtime cost far exceeds the cable.

Packaging, Printing and Plastics: Fast + Oily

These lines combine two stresses: fast reciprocating motion and a working environment full of oils, grease and coolant mist. The motion pushes you toward high-flex; the environment pushes you toward an oil-resistant PU jacket. If the machine runs wet or in a wash-down area, PU is the safer default over a PVC jacket, which can harden and crack with repeated oil and chemical exposure.

Industrial and Collaborative Robots: Flex in Every Axis

Robot and cobot arms bend cables across multiple joints, through tight radii, at high cycle counts. This is the most demanding flex case on the list. Pick a high-flex grade with fine stranding and a jacket designed for bending, and respect the manufacturer’s minimum bend radius. For cobots with compact arms, cable diameter and weight also matter — a lighter, thinner cable adds less load to the arm.

Lithium Battery and Welding: Shield Against EMI

Lithium-battery formation and welding equipment generate strong electromagnetic noise that can corrupt encoder feedback. Here the shield is the whole point. Look for a cable with a multi-layer shield construction — TENSOlink offers a three-layer shield option tuned for exactly these high-interference environments — so the position signal reaches the drive cleanly. A thin, single-foil shield that works on a quiet CNC may not be enough next to a welder.

Medical Equipment: Clean and Chemical-Resistant

Medical and lab automation cables flex gently but must tolerate repeated cleaning and chemical agents, and shed little particulate. A PU jacket is the natural fit: chemical-resistant, smooth, easy to wipe down. Confirm any device-specific flammability or biocompatibility requirements with the equipment maker before specifying.

What Still Has to Match

The application chooses the cable construction. The drive side must still match exactly:

  1. Part number / pinout — same as the original Siemens or third-party part you are replacing.
  2. Shield and ground design — power and encoder shields must land correctly.
  3. Cross-section — sized for the motor’s current and the cable length.
  4. Connector — the mating connector on the drive and motor must be the right one.

Where TENSOlink Fits

TENSOlink builds replacement servo cables across all five application families, in the three jacket grades covered earlier — SG (high-flex drag chain), EG (fixed installation) and PU (oil- and chemical-resistant) — with the same pinout and part numbers as the originals. That means one supplier can cover a mixed shop floor: CNC, packaging, robots, battery lines and medical automation, all from the same program. Our sister brand Mosen supplies the mating connectors (straight and right-angle, custom shielding, IP67 overmoulded options), so cable and connector are matched from one source.

Frequently Asked Questions

Which servo cable do I need for a CNC machine?
A drag-chain (SG) high-flex cable rated for continuous flex — TENSOlink SG is specified for 10 million flex cycles — routed in a proper cable carrier.

Which servo cable for robot arms and cobots?
A high-flex grade with fine stranding and a jacket built for tight bending, plus careful attention to bend radius and, for cobots, cable weight and diameter.

What cable should I use for lithium-battery or welding equipment?
A shielded cable built for strong EMI. TENSOlink offers a three-layer shield construction tuned for high-interference environments like battery formation and welding.

Can I use one servo cable type for all my machines?
Only if all your machines have the same motion and environment. Mixed lines usually need a mix of grades — high-flex for moving axes, fixed-installation for cabinets, PU for oily or chemical areas.

Does the application change the shielding requirement?
Yes. Quiet CNC axes tolerate lighter shielding, but welding and battery equipment need a robust multi-layer shield to keep encoder feedback clean.

Does TENSOlink cover all these applications?
Yes — SG, EG and PU grades across CNC, packaging, robotics, battery and medical applications, with matching connectors from sister brand Mosen.

What lengths can I order?
Standard lines run from 0.3 m to 70 m (and longer on request depending on the series); contact us for exact per-series ranges.

About TENSOlink

TENSOlink (Guangdong) supplies OEM-compatible servo cables for Siemens V90, S120 and S210 systems, in high-flex, fixed-installation and oil-resistant grades. Visit our contact page for a quote.

References