Direct answer: Most servo-cable failures announce themselves before the machine stops. The warning signs are usually intermittent — a drive fault that clears on a restart, a position error that appears only when an axis moves, or an alarm that comes back on a cold morning. The five common failure modes are conductor fatigue (from repeated bending), shield/ground faults (noise and earth-current errors), insulation breakdown (moisture, oil, heat), connector wear (contact resistance and signal drop), and jacket damage (the visible start of the others). Confirm with a continuity test, an insulation-resistance (megger) test, and a shield-continuity check, then replace — do not splice a failed servo cable. Match the new cable’s part number, shield design and jacket grade to the machine, not just the price.
The 5 Failure Modes and How Each Shows Up
| Failure mode | Typical symptom | Root cause |
|---|---|---|
| Conductor fatigue | Intermittent open / axis drops only while moving | Fixed-grade cable used in a drag chain, or bend radius too tight |
| Shield / ground fault | Drive ground fault, position noise, comms errors | Damaged or poorly terminated shield, ground loop |
| Insulation breakdown | Megger reads low, trips on damp starts | Moisture, oil, coolant, or heat ingress |
| Connector wear | Signal dropouts, encoder errors, heat at the connector | Cycles, vibration, corrosion, bent pins |
| Jacket damage | Abrasion, cuts, flat spots | Rubbing, pinch, wrong jacket for the environment |
1. Conductor Fatigue — The Moving-Axis Killer
Copper work-hardens and eventually breaks after too many bends. A cable rated for a few thousand cycles will fail early inside a drag chain that flexes it millions of times. The tell-tale sign is a fault only when the axis moves — the drive runs fine while parked, then throws an error at the same point in the stroke where the broken strand makes and breaks contact.
- Intermittent open circuit that tracks the travel position
- Failure clustered where the cable flexes most (chain entry/exit)
- A fixed-installation cable (EG grade) wrongly used on a moving axis
The fix is a cable with the right flex rating and stranding — a fine-stranded, high-flex grade (SG) rated for the machine’s cycle count, not a cheaper fixed cable. TENSOlink SG cables are specified for 10 million flex cycles. See the jacket-grade guide for which grade fits your motion.
2. Shield and Ground Faults — Noise and Drive Errors
The shield protects the encoder/feedback signal and drains interference to ground. When it is nicked, unterminated, or left floating, the symptoms are electrical and often confusing:
- Drive reports a ground fault or overcurrent with no obvious short
- Encoder position jitters or drifts with no mechanical cause
- Fieldbus / DRIVE-CLiQ communication errors that appear and vanish
- Problems that get worse near VFDs, welders or other noise sources
Check shield continuity end-to-end and confirm the shield is terminated at the intended point (usually 360° at the connector shell). In high-EMI cells (battery formation, welding), a light single-foil shield may not be enough — a multi-layer shield construction holds the feedback clean.
3. Insulation Breakdown — Moisture, Oil and Heat
Insulation fails when its jacket is attacked or it runs too hot. Once moisture, coolant or oil reaches the conductors, insulation resistance drops and current leaks.
- Megger / insulation-resistance reading falls below spec
- Trips that appear only on cold or damp starts, clear once warm
- Discoloration, swelling or a “wet” feel along a run
The usual cause is the wrong jacket for the environment — a PVC cable in an oily wash-down area hardens and cracks, letting ingress in. Match the jacket to the environment (PU for oil/chemical/wash-down).
4. Connector Wear — The Most Overlooked Fault Point
More servo problems start at the connector than in the cable body. Contacts wear, pins bend, and oxidation raises contact resistance.
- Signal dropouts under vibration
- Encoder/feedback errors, heat visible at the connector
- Intermittent faults that change when you wiggle the connector
Reseat and inspect pins first; look for corrosion, bent contacts or a worn latch. If the connector is damaged, replace it rather than taping over it — a high-integrity mating is part of the signal path.
5. Jacket Damage — The Visible Warning
Cuts, abrasion and flat spots are how the other four modes usually begin. A nicked jacket eventually reaches insulation, then shield, then conductor. Treat a visibly damaged jacket as a scheduled replacement, not a cosmetic issue — inspect it regularly on high-cycle runs.
How to Test a Suspect Servo Cable
Test with power isolated; never test live. A quick, repeatable sequence:
- Visual — jacket, bend zones, connector shells (look for cuts, flat spots, heat discoloration, corrosion)
- Continuity — every conductor end-to-end; look for high or intermittent resistance
- Insulation resistance (megger) — conductor-to-conductor and conductor-to-ground at the drive’s test voltage; compare with spec
- Shield continuity — shield to shield, plus shield-to-ground termination
- Flex-under-test — move the axis while watching the reading, to catch faults that only appear in motion
A meter and megger find most problems; a cable that passes all five but still faults is the rare high-frequency/intermittent case — swap in a known-good cable to confirm before condemning the machine.
When to Replace (Not Repair)
A servo cable is a field-replaceable consumable, not a repairable part. Replace it when:
- Any conductor is broken or insulation resistance is below spec
- Shield is nicked or continuity is lost
- Jacket is cut, oil-soaked or hardened
- The machine’s motion or environment changed and the old grade no longer fits
Do not splice or re-terminate a failed power/encoder assembly in the field — a poor repair on a moving, EMI-sensitive line becomes a new failure. If the cable ran in a drag chain to end-of-life, replace the assembly with the correct flex grade.
Getting the Replacement Right (Match Three Things)
A replacement only clears the fault if it matches what the machine needs:
- Electrical match — pinout and part number; the cross-reference guide shows how to find the right part.
- Mechanical match — flex grade and bend radius for the motion; verify single- vs dual-cable if the topology is unclear.
- Environmental match — jacket and shielding for oil, EMI or clean use; see the application guide.
A frequent root cause on OEM-vs-aftermarket lines is a cable that electrically matched but had the wrong grade. For the difference, read OEM vs aftermarket servo cables.
Frequently Asked Questions
What is the first sign a servo cable is going bad?
Intermittency. A fault that clears on restart, or an axis error that only appears while moving, is usually a cable/conductor fatigue or shield fault, not a mechanical problem.
How do you test a servo cable without power?
Continuity on every conductor, an insulation-resistance (megger) test, and shield-continuity plus shield-ground checks. A cable that reads fine but still faults is often high-frequency interference — confirm by swapping a known-good cable.
Why does my drive report a ground fault but nothing is shorted?
Usually the shield: damaged, unterminated, or ground-looped. A multi-layer shield correctly terminated to the connector shell clears most of these.
Can I repair a cut servo cable instead of replacing it?
Not reliably. On moving, EMI-sensitive power/encoder assemblies, a field splice or re-termination tends to become a new failure point. Replace the assembly with the correct grade.
How long does a servo cable last?
Driven by cycle count, not calendar time. A drag-chain axis flexes the cable millions of times; the correct high-flex grade is rated for that cycle life. Match the flex rating to the machine.
What causes a cable that fails over and over after replacement?
The replacement is the wrong grade (fixed cable on a moving axis), a too-tight bend radius, or a jacket that can’t take the oil/temperature. Fix the cause before the next cable fails too.
Which TENSOlink cable replaces a failed one?
Match part number/pinout, flex grade and jacket to the original and the environment. If the old cable ran in a chain, use the SG high-flex grade.
About TENSOlink
TENSOlink (Guangdong) supplies OEM-compatible servo cables for Siemens V90, S120 and S210 systems, in high-flex, fixed-installation and oil-resistant grades, matched to the original part number and pinout. Sister brand Mosen supplies the mating connectors. Visit our contact page for help identifying a replacement.
References
- Siemens SINAMICS V90 / S210 servo drive systems
- TENSOlink — Servo Cables
- Directive 2014/35/EU (Low Voltage) — insulation and safety